After clicking Wizard page, you can set device in Gateway Mode, Repeater Mode, WISP and AP Mode (Default Selection). It provides flexibility to configure wireless AP’s operation mode based on network scenario making this AP future proof. You are required to select corresponding operation mode first before starting the configuration. Clicking Wizard will pop up following page to configure the operation mode along with photos with explanation for each operation mode.

Gateway Mode:
In Gateway mode, all Ethernets are bridged together and wireless clients will connect ISP access point or router connecting directly to the Internet via WAN PORT. NAT is enabled and PCs in Ethernet LAN port share the same IP to ISP through wireless LAN.

WISP Mode:
In WISP mode, the device connects to ISP station or hot spot wirelessly to share network with local wired and wireless devices.

Repeater Mode:
In Repeater mode is used to extend the range of wireless coverage of existing Wi-Fi network. This mode is suitable when you are in a Wi-Fi dead-zone or a place with weak wireless signal, and you want to have a larger effective range of the wireless signal throughout your home or office.

AP Mode:
In AP mode, the device works as an access point to transform your existing wired network into a wireless network.

2.1 Gateway Mode

In Gateway mode, your internet provider's RJ-45 is connected to WAN port of AP750. Internet provider WAN setting can have Static IP, PPPoE, or DHCP accordingly select option. Then configure the wireless parameters as per your choice of SSID, Channel width, Encryption and Time reboot if required.

Fig 2.1.1 Gateway mode of AirONE AP750

Fig 2.1.2  Gateway mode WAN Setting of AirONE AP750

Note:
You can set SSID name and encryption and password as per requirement. Please turn ON Wi-Fi Status to make it active

Fig 2.1.3  Gateway mode 2G Wi-Fi Setting of AirONE AP750

Fig 2.1.4 Gateway mode 5G Wi-Fi Setting of AirONE AP750

Note:
The device will restart for the changes to take effect for mode changes to Gateway mode.

Home page will show LAN, WAN, Wi-Fi, Device Information, along with operation mode shown as below.

Fig 2.1.4 Gateway mode Home page of AirONE AP750

2.2 WISP Mode

In WISP mode, Scan Repeater SSID whose password is known and configure WAN setting. Then configure the wireless parameters as per your choice of SSID, Channel width, Encryption and Time reboot if required.

Note: Just in case if you don’t have any RJ 45 cable running to any room then In WISP mode you have to just power on the device and wirelessly can connect to clients as well as ISP router (BSSID). No need of connecting physically LAN as well as WAN port. So, can help to make auditorium online without any cabling.

Fig 2.3.1 WISP mode of AirONE AP750

Fig 2.3.2 2G Repeater Setting WISP mode of AirONE AP750

Fig 2.3.3 5G Repeater Setting WISP mode of AirONE AP750

Fig 2.3.4 Repeater SSID for 2G repeater WISP mode of AirONE AP750

Note: This repeater SSID password is password of scan SSID with matching encryption.

Fig 2.3.5 WAN Setting WISP mode of AirONE AP750

Note:
You can set SSID name and encryption and password as per requirement. Please turn ON Wi-Fi Status to make it active

Fig 2.3.6  2G Wi-Fi Setting WISP mode of AirONE AP750

Fig 2.3.7 5G Wi-Fi Setting WISP mode of AirONE AP750

Note:
The device will restart for the changes to take effect for mode changes to WISP mode.

Home page will show WAN, Repeater, Wi-Fi, Device Information, along with operation mode shown as below.

Fig 2.3.8 WISP mode Home page of AirONE AP750

Fig 2.3.9 WISP mode Ping response of Client of AirONE AP750

2.3 Repeater Mode

In Repeater mode, scan the Repeater SSID whose password is known. Then configure the wireless parameters as per your choice of SSID, Channel width, Encryption and Time reboot if required.

Suggestion:
Just in case if you don’t have any RJ 45 cable running to any room then In Repeater mode you have to just power on the device and wirelessly can connect to clients as well as ISP router (BSSID). No need of connecting physically LAN as well as WAN port. So, can help to make auditorium online without any cabling.

Fig 2.3.1 Repeater mode of AirONE AP750

Fig 2.3.2 Selecting 2G Repeater SSID of AirONE AP750

Note: This repeater SSID password is password of scan SSID  with matching encryption.

Fig 2.3.3 Selecting 5G Repeater SSID of AirONE AP750

Fig 2.3.4 Repeater 2G SSID password AirONE AP750

Note: You can set SSID name and encryption and password as per requirement. Please turn ON Wi-Fi Status to make it active.

Fig 2.3.5 Setting 5G Wi-Fi setting of AirONE AP750
 

Fig 2.3.5 Setting LAN setting in repeater mode of AirONE AP750

Note:
The device will restart for the changes to take effect for mode changes to Repeater mode.

Home page will show LAN, Repeater, Wi-Fi, Device Information, along with operation mode shown as below.

Fig 2.3.6 Repeater mode Home page of AirONE AP750

2.4 AP Mode

In AP mode, Set LAN setting from static IP, AC or gateway. Then configure the wireless parameters as per your choice of SSID, Channel width, Encryption and Time reboot if required.

Note: This is a default mode of operation for device.

Fig 2.4.1 AP mode of AirONE AP750

Fig 2.4.2 Setting IP mode of AirONE AP750

Note: You can set SSID name and encryption and password as per requirement. Please turn ON Wi-Fi Status to make it active

Fig 2.4.3 Setting 2G Wi-Fi for AP mode of AirONE AP750

Fig 2.4.4 Setting 5G Wi-Fi for AP mode of AirONE AP750

Note: The device will restart for the changes to take effect for mode changes to AP mode.

Home page will show LAN, Repeater, Wi-Fi, Device Information, along with operation mode shown as below.

Fig 2.4.5 Home page after setting AP mode of AirONE AP750